Hunter 44360 Programmable Thermostat Installation Instruction

Hunter 44360 Programmable Thermostat 

Congratulations!
Thank you for choosing a Hunter programmable thermostat. Your new Hunter thermostat will provide years of reliable service and year-round energy savings. Please read this manual before beginning installation and save this booklet for complete operation instructions.

important information

This thermostat is designed to work on the following heating and cooling systems:

• Gas–Standing Pilot
• Gas – Electronic Ignition
• Gas – Fired Boilers
• Gas – Millivolt Systems
• Oil – Fired Boilers
• Oil – Fired Furnace
• Electric Furnace
• Electric Air Conditioning
• Single-Stage Heat Pumps

This thermostat is not designed for multi-stage heat pump systems or 110/220 V baseboard heating systems. If you are unsure what kind of heating and cooling system you have, please contact a qualified HVAC Technician for assistance.

Tools

This thermostat includes two #8 slotted screws and two wall anchors for mounting.
To install your new thermostat, you will need the following
supplies:
Flat-head screwdriver
…………………………………………………………………………………
Small Phillips-head screwdriver
…………………………………………………………………………………
Hammer
…………………………………………………………………………………
Electric drill and 3/16” bit
…………………………………………………………………………………
Two 1.5 Volt (AA) size alkaline batteries
………………………………………………………………………………..

NOTICE! Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ensure proper reconnection.

uninstalling the existing unit

1. Turn the system power OFF from the existing thermostat. Turn the power to the HVAC system is OFF at the main power panel or at the furnace. (Failure to turn off the power to the existing thermostat before removal could damage your system.)
2.  Remove the existing thermostat cover to access the wires from the wall. (Some thermostats may have multiple covers, screws or other locking devices that must be removed or disengaged. See page 8 for common examples.)
3. Locate, but do not disconnect the wires. (If wires are not visible, they may be connected to the back of the wall plate. Some models may have doors that open to expose the wires and mounting screws.)

wire labels

uninstalling the existing unit, cont

• Using the provided stickers, label each wire according to the Wire Labels chart. (If the terminals are not labeled, contact a qualified HVAC technician.)
  Note: Wire colors do not always comply with standards, so wire colors should be ignored. Refer to the existing terminal designation for proper identification.
• If wires marked Y & C are both present, C may be a Common wire and should not be used. If you have a wire marked C, do not connect it to any terminal. This wire is used only for non-battery-powered thermostats. Do not let the wires slip back

installing the thermostat

1. Remove the wall plate from the new thermostat by pressing the release tab on the bottom of the thermostat.
2. Position the new wall plate on the wall and pull the labeled wires through the opening.
3. If the existing holes do not match those on the Hunter wall plate, or if there are no existing holes, visually level the wall plate and mark the wall for two holes.
4. Remove the wall plate and drill two 3/16” holes where marked.
5. Tap the plastic anchors into the holes until they are flush with the wall. (Do not use plastic anchors if you encounter a stud in the wall.)
6. Reposition the wall plate on the wall, pulling the wires through the opening. Insert the mounting screws through the wall plate and into the anchors. Verify that the wall plate is visually level and securely tighten both screws.

installing the thermostat, cont

1. Loosen, but do not remove, the terminal screws.
   Note: A jumper wire has been provided, connecting the RC and RH terminals for systems that do not provide both an RH and RC wire. If you have both an RH and RC wire, remove this jumper. If you do not have both an RH and RC wire, leave the jumper in place.
2. Match and connect the wires from the wall to the terminals as shown. Wires should be inserted behind the black terminal shields. Tighten each screw after the connection has been made  (The ends of any extra wires should be individually wrapped in electrical tape and carefully pushed back into the wall.)
3. Push any excess wire length back into the wall to prevent interference.

ATTACHING THE THERMOSTAT
Lift the thermostat cover and set the SYSTEM switch to OFF and the FAN switch to AUTO.

1. Fan option – Locate the HE/HG switch on the back of the thermostat. Set the switch to HG (default) for gas furnaces and oil burners. Set the switch to HE for electric furnaces. (The switch has no effect when the system is set to cooling mode.)
2.  Recovery – Locate the Auto Recovery switch on the back of the thermostat. If you wish to use the Energy Star-compliant Auto Recovery feature, verify that the switch is in the ENABLE position. If you do not wish to use this feature, simply change the switch to the DISABLE position. See pages 44-45 for more information.
3. System type – Locate the System Type switch on the back of the thermostat. Select either STD (Standard) or HP (Heat Pump) to match your system.
4. Place the top of the thermostat over the two tabs on the wall plate. Press the thermostat onto the wall plate and press to snap the bottom tab into place. Note: Do not force the thermostat onto the wall plate, as the terminal pins may be damaged. If the thermostat does not sna
   into place properly, the unit may not work.
5. Lift the front cover and insert two AA alkaline batteries.
6. Restore power at the electrical panel or furnace.

settings

The default setting of the thermostat is Fahrenheit (Fo). (NOTICE: CHANGING THIS SETTING WILL RESET THE THERMOSTAT TO FACTOR Y DEFAULT PROGRAMS.)
To change to Celsius (Co):

1. Press and hold the Up button.
2. Use a paperclip to press the Reset button.
3. Continue to press the Up button, but release the Reset button when the LCD turns on. To reset the unit to F, press only the Reset button.

SETTINGS, cont
The default for this thermostat setting is in a 12-hour format. You can change the format to 24-hour format by pressing Day/ Time and then Program.
The AM/PM indicator will be off when the thermostat is in 24 hour mode.

1. Press Day/Time. (AM/PM and current hour will flash)
   Press Up or Down to adjust the setting.
2. Press Day/Time again to adjust the minute setting.
   Press Up or Down to adjust the setting.
3. Press Day/Time again to adjust the day of the week.
   Press Up or Down to adjust the setting.
4. Press Day/Time to return to the normal display.
   Press Up or Down to adjust the setting. You may also press Hold/Return at any time to return to the normal display.

methods of operation

This thermostat gives you the ability to program up to 4 custom temperature settings per day or utilize pre-programmed settings. For manual operation instructions, see pages 28-31. To utilize the pre-programmed settings, see pages 32-33.
To create custom programs, see pages 34-37.

MANUAL OPERATION
Many people prefer to operate their thermostats manually, adjusting settings as needed. You can either temporarily override the settings for the current program, or permanently override all settings and adjust temperatures manually  If you want to only override the current pr gram:

1. Press and hold Up or Down for one second to enter Manual Override mode. (Release the button when the display flashes.)
2. Press the Up or Down buttons to adjust the temperature setting as desired. The system will revert back to the program at the next scheduled program time

MANUAL OPERATION, CONT.
If you want to permanently override all settings and adjust the thermostat manually:

1. Press Hold/Return until the Hold icon appears.
2. Press and hold Up or Down for one second to enter Manual Override mode. (Release the button when the display flashes.)
3. Press the Up or Down buttons to adjust the temperature setting as desired.
4. Press and release Hold/Return to return to the normal display.

DEFAULT PROGRAMS
This thermostat meets ENERGY STAR guidelines for energy efficiency. By using the pre-programmed settings, this thermostat can save you money by optimizing energy usage in heating and cooling  Refer to the Default Programs Chart for detailed information about the pre-programmed settings.

CREATING CUSTOM PROGRAMS

Program times can be set in 10-minute increments.

• Program temperature can be set in increments of 1o F (1o C).
• After 15 seconds of inactivity during programming, the thermostat will return to Normal Display mode.
• When setting each program time, note the AM/PM indicator.
• Press Hold/Return at any time to exit Program mode and save your settings.
• During normal operation, if no button is pressed for 5 seconds, the unit will return to the Normal Display mode.

1. Slide the system switch to HEAT or COOL to program the corresponding system.
2. Press Program to enter Program mode. (The LCD will begin to flash)
3. Press Up or Down to change the hour. Press Program to save the hour and adjust the minute setting.
4. Press Up or Down to change the minute. Press Program to save the minute setting and adjust the temperature.
5. Press Up or Down to change the temperature. Press Program again to move to the next program number. (There are 4 programs per day. If you do not wish to assign 4 programs per day, set up to 4, keeping in mind that the total program time must equal 24 hours.)
6. Repeat steps 2-5 for the remaining days.
7. To review your program settings, press Program repeatedly to review the customized programs. (You can make changes at any time when the thermostat is in Program mode.)
8. Slide the system selector switch to the opposite position and repeat steps 2-5.

ICONS AND FEATURES

INDIGLO® night-light – will backlight the display

1. INDIGLO® night-light – will backlight the display for easy viewing in the dark. Press any button to illuminate the light. (If no button is pressed after 5 seconds, the backlight will turn off.) Note: If the thermostat shows a Low Battery Warning, the backlight will not operate. Follow the instructions on pages 42- 43 to change batteries.
2. Filter change indicator – will flash after 400 hours of system use as a reminder to check or change your filter. Press and hold the Filter button for 3 seconds after changing the filter to reset the filter timer. (Pressing the Filter button for less than 3 seconds will cause the Filter change indicator icon to appear. The filter timer will not be affected unless the button is held for more than 3 seconds.) Note: Clearing the Filter counter will also clear the Energy counter. See pages 50-51 for more information.
3. Span setting mode – allows you to adjust the system ON/OFF cycle rate. The default setting is 2 (the system cycles ON or  OFF when the temperature is within 1o F (0.5o C) above and below the set temperature.) The span setting can be adjusted if your system is cycling too fast or too slowly. Press and hold both the Up and Down buttons until the word SPAN appears. Use the Up or Down button to adjust the span setting. (Up will increase your cycle time by allowing the system to run longer; Down will decrease your cycle time by causing the system to run for a the shorter length of time.) Span settings remain the same for HEAT and COOL system settings. When batteries are installed, or the unit is RESET, the span cycle will revert to 2.
4. Low battery warning – indicates two stages of battery power shortage. When the batteries are detected as weak, the icon will flash until new AA alkaline batteries are installed (Stage 1). I  the batteries become too weak for normal operation, the thermostat enters the second battery power shortage mode (Stage 2). When insufficient battery power is left, the battery icon will flash alone on the display and your system will turn off. The display will be blank when no battery power is left. The system will remain off until new batteries are installed. (Your programs and time settings will be lost if the batteries are not replaced within one minute.) The thermostat will resume normal operation after new batteries are installed.
5. Auto recovery – allows heating and cooling systems to gradually recover from an energy-saving setpoint temperature to a comfortable setpoint temperature. Auto recovery calculates the time needed to adjust the temperature to the next program setting. When the thermostat is in Auto Recovery mode, the display will flash alternating messages of RECO and the time. Auto Recovery can be disabled by sliding the recovery switch on the back of the circuit board to the disable position. (Auto Recovery will not operate if Permanent or Temporary holds are on.) Press Hold/Return during the Auto Recovery process to
   manually cancel the recovery.
6. Error mode – indicates an unexpected battery problem. The screen will flash an ERR message and shut your system off until the batteries are replaced with new AA alkaline batteries. You must Reset and reprogram the thermostat after replacing the batteries if the thermostat has entered Error mode.
7. Auto cut off – automatically turns the system off if the temperature rises above 95o F (35o C) or drops below 40o F (4o C). (If your HVAC system has malfunctioned, the system will no longer respond to thermostat controls and the Auto cut-off will have no effect.)
8. Home Today – overrides the programmed settings during a time you would not normally be home. Pressing Home Today during the first or second programs of the day will override the programs until the fourth program begins. The thermostat will then go back into Normal mode. Pressing Home Today during the third program of the day will override the programs until the first program of the next day.
   Press Home Today to enter or exit the program override. The “Home Today” message will flash on the screen and the program number will disappear. The highest or lowest schedule of the program will appear for you to adjust. Press Up or Down to adjust the temperature.
9. Energy – calculates energy usage. Press to display the total operation time for heat and air conditioning for today, yesterday, last week, or Total. Monitoring energy usage allows you to optimize energy savings. Press Energy to cycle through Today, Yesterday, This Week, and Total (up to 999 hours and 59 minutes). Press and hold Energy until the display blinks to reset the counter. Note: Clearing the Energy monitor counter will also clear the Filter counter. 10. Daylight savings time – allows for an easy transition during daylight savings time. Press Day/Time, then Up or Down to enter daylight savings time mode and adjust as needed.

Important features

1. Temperature Range
2. Compressor Protection After the system stops running in cooling mode, there will be a 3.5-minute delay before it can be restarted to prevent compressor damage due to rapid cycling.
3. Resetting the unit To restore the thermostat to the original factory settings, press the reset button with a paper clip. (This will erase any user-programmed settings.)

Troubleshooting

1. My display will not come on.
   •  Check batteries and battery connections.
   • Reset the thermostat.
2. The auto fan feature will not operate properly.
   • Remove the thermostat from the wall plate and set the HG/HE switch to the correct position.
3. My display is erratic.
   •  Reset the thermostat and reprogram your settings.
4. The program will not change at my desired setting.
   •  Check that the time is set properly to AM or PM.
   • Make sure the thermostat is not in permanent override mode.
   • Check that the day setting is correct.
5. My heating or cooling will not turn on or off.
   • Check the Heat/Cool function switch to ensure it is set to the desired position.
   • Wait. There may be as much as a 4-minute delay before the system turns on or off to protect the compressor.
   •  Check the circuit breakers and switches to ensure there is the power to the system.
   • Replace the batteries.
   • If applicable, make sure the furnace blower door is closed properly.
   • If your system has 4 wires, ensure the jumper wire is installed between the RC and RH terminals.
   • Check your system for proper wiring.
6. The display will come on, but it will not stay illuminated.
   • Replace batteries
7. My system continues to operate when the thermostat is in the off position.
   • Replace unit.
   • Check your system for proper wiring.
8. The LCD screen permanently reads HI, LO, or ERR.
   • Replace unit.
9. How do I just operate my thermostat manually?
   • Manual operation instructions are on pages 28-31.

Is there help on the web?
Yes. Visit http://www.hunterfan.com for more information.
Can’t I just call someone?
Sure. The Hunter Technical Support Group is available from 7 am to 7 pm CST M-F and 8 am to 5 pm Saturday. They may be reached toll-free at 1-888-830- 1326.

REFERENCE:

Download Manual:

Hunter 44360 Programmable Thermostat Installation Instruction

Hunter 44360 Programmable Thermostat Installation Instruction

The post Hunter 44360 Programmable Thermostat Installation Instruction appeared first on thermostat.guide.

source https://thermostat.guide/hunter/hunter-44360-programmable-thermostat-installation-instruction/