SALUS EP110 Single channel programmable Thermostat Installation Manual

SALUS EP110 Single channel programmable Thermostat

Product Compliance

This product complies with the essential requirements and other relevant provisions of the following EU Directives: 2014/30/EU, 2014/35/EU, and 2011/65/EU. Please check www.saluslegal.com for the full information.

Safety Information
Use in accordance with the EU and national regulations. For indoor use only. Keep your device completely dry. This product must be installed by a competent person and in accordance with all the EU and national regulations Always isolate the AC Mains supply before installing or working on any components that require 230 VAC 50Hz supply.

Box Content

The box includes the EP110 controller, 2X screws and plugs, and the Quick Guide installation manual.

Introduction

A programmable heating controller is used to switch the heating system and/or hot water in your home as needed. It works by controlling the heating boiler according to a series of programmed settings that take effect at different times of the day. The controller can be set up to 3 programs per day, with complementary Boost actions, and can operate in five different modes. Three different sets of times can be set for each day of the week, resulting in a total of 21 settings applicable to the device. When connected to a system with a non-programmable (digital) thermostat, it can switch off/on the boiler and control the heating and/or hot water in your system in a programmed manner. You can use the controller in a fully pumped and controlled system, where heating and hot water can be operated independently, or in the gravity-fed water system, where central heating cannot be operated without hot water.
The heating system will not work if the programmer has switched it off. The controller does not detect the temperature or adjust the heating mode in your house, it just tells the boiler when to switch Off/On depending on our individual time settings.  With the controller, you don’t have to worry about switching On/Off your system manually. All you need to do it so set up the schedules that fit your needs. The controller can be used on your system to control either the central heating OR the hot water.

Features

• Single Channel Programmer for Central Heater or Hot Water
• 12 or 24-hour clock format
• 5+2 or 24 h individual program with 3 settings per day
• Boost function
• Holiday function
• Advance function
• Memory backup

Installation

Wiring and terminal description

Volt-free application. Note: Please remove the red link wire (like the one in the picture above) for this application.

Wall mounting

Jumper settings
The jumpers are found on the rear of your controller and can be used to change the settings for the program type or internal backup memory battery. If you want to change the position of your jumpers, please note that you will need to reset your device. The default position for the jumpers set a 5+2 program type and keeps the internal backup battery off.

Note: Changes to the jumper settings should only be made by the engineer carrying out the installation or another qualified person. The installer should select the jumper positions required if changes need to be made to the factory default settings. These jumpers are found on the rear of the controller.

Button functions and LCD icons

1. Showing when the relay is On
2. Boost hours
3. Daylight Saving Time On/Off
4. Program number
5. ON Mode Active (controller runs continually)
6. ONCE Mode Active (controller runs for 1 period a day)
7. Auto Mode Active (controller runs in Auto)
8. ADV Mode Active (controller runs in advance override)
9. OFF Mode Active (controller is off )
10. AM/PM
11. Holiday mode on
12. Days of the week

Operations

Initial power up
After powering up or after RESET is pressed, the programmer is reset to factory default settings. During the system reset, all LCD icons and segments are turned on for 2 seconds and all keys are blocked. After 2 seconds and all keys are released, the programmer is initialized. First, the software version is shown and after that, the typical reset display is shown. The time should be 12:00am.

Default settings

Function	Status after Reset
Operation Mode	Normal mode
Clock	12:00 AM
AM/PM indicator	AM
Date	January 1, 2016
Daylight Saving Time(DST)	On
Program	Factory default 5+2
Program Number indicator	Off
SET indicator	Off
PROG indicator	Off
Mode indicator(s)	“Off“
Output Relay	Off
CH/HW indicator(s)	Off

Setting time and date
The first thing you will have to do is to set the time and date on your controller. First, you will need to set up the time and then the date. To enter clock setting mode, press and hold the Select and Set buttons for 3 seconds. Please follow the instructions below.

Setting time and date
The first thing you will have to do is to set the time and date on your controller. First, you will need to set up the time and then the date. To enter clock setting mode, press and hold the Select and Set buttons for 3 seconds. Please follow the instructions below.

Operating Modes
EP110 can operate in 5 different modes, described in the table below. EP110 can be set to control either the boiler OR the hot water. You can choose on which one of the channels you connect the controller. To access operating modes, please press the Mode key

Operation Mode	Function
ON	Continuously on
ONCE	On for 1 period a day, from Program 1 ON to Program 3 OFF
AUTO	Automatic program control
ADV	When device is in Auto or Once mode, press the MODE button for 3 sec for selecting Advance (ADV). This will move the unit into the next program. When the ADV function ends the device will return to normal program.
OFF	Continuously off

For activating the functions described above, press the MODE button. The operating mode is cycled in the below sequence:

ON Mode

• Pressing the Mode key 3 times activates the AUTO. In AUTO mode, the controller gives the boiler the ON/OFF command depending on your schedule.
• Pressing the Mode key 4 times activates the OFF Mode. In OFF mode, the controller gives the boiler the OFF command, so the heating or the hot water will be turned off.

ADV Mode
Note: In ONCE or AUTO mode, by long pressing the MODE button, the controller will switch automatically to ADV. You can cancel the ADV by long-pressing the MODE key. The device will then return to ONCE or AUTO mode. You can’t select ADV by pressing the Mode key.

When in Auto mode selecting ADV, the controller will simply toggle the current auto setting (ON or OFF). For example, if the current program is set as:

Selecting ADV between 8:00 and 8:59 will change the output to OFF, from 9:00 onwards back to AUTO (which is also OFF). Selecting ADV between 9:00 and 09:59 will change the output to ON, from 10:00 onwards back to AUTO (which is also ON). If the ADV puts the relay ON then the boost would apply immediately at the next OFF change, if the ADV puts the relay OFF then the boost would apply immediately and turn the relay ON.

If ADV occurs at 08:30 and the relay is ON from 08:30 to 12:00. During this period, if at 08:45 +1Hr (Boost) is pressed, the relay will be ON from 08:30 to 12:00. Boost is applied immediately ie. from 08:45 to 09:45 at the next change, ie. 12:00. If ADV occurred at 10:30 the relay will be ON from 10:00, OFF from 10:30 (ADV) to 14:00 if no +1Hr Override. During ADV, if at 10:45 +1Hr (Boost) is pressed, the relay will go ON again at 10:45 (boost starts), OFF at 11:45 (Boost ends) until ends at 14:00, then ON again at 14:00.

Programming the EP110
2 types of programs can be set:

• 5+2 (Mo to Fri same and Sat, Sun same)
• Different programs for each 24h. There are 3 different time sets for each day.

5-2 Days Program	Individual Days Program
Weekdays 3 sets of time/channel Weekends 3 sets of time/channel Total: 6 settings/week	1 Day 3 sets of time/channel     Total: 21 settings/week

Setting the 5+2 program

Once you have finished setting the start/end time for the first program, the device will jump into the second program, then into the third, and afterward into Sat-Sun. Please follow the same steps for each of the 3 programs. Press SET at any time to confirm the setting and return for program set selection.

Setting different programs for each 24h

Note: Don’t forget to move the jumpers to 24h in order to have the individual program active. After that please follow the same instructions as for the 5-2 days program.

Once you have finished setting the start/end time for the first program, the device will jump into the second program, then into the third, and afterward into the next day. Please follow the same steps for each of the 3 programs. Press SET at any time to confirm the setting and return for program set selection.

Functions

Temporary Override
Boost Override (+1Hr override)
Boost Override (+1Hr override) is available in ONCE/AUTO/OFF modes. Boost mode can be activated even in ADV mode. When boost mode is activated, ADV is canceled. Press +1Hr at the current mode to activate the Boost Override (+1Hr override) setting mode. Boost mode increases the time of the active program by 1-9 hours. The new setting hour “+x” (x=last boost hour+1 hour) is displayed. A subsequent press of +1Hr will increase the duration by 1 hour. The maximum duration is 9 hours. If the number rolls back to blank, this will disable the Boost Override.

ADV Override
ADV only works in AUTO or ONCE mode. During ADV, press MODE once to cancel ADV and go back to AUTO /ONCE mode after the LCD backlight is turned off. +1Hr override and ADV cannot co-exist in the same channel. During ADV mode, when +1Hr is pressed, override mode will cancel ADV mode and then change to Boost mode. If +1Hr override (Boost) is running, then ADV is selected, ADV will be activated and the previous +1Hr override will be canceled.

Holiday Override
During the period of holiday override, the relay should be always Off. Press and hold at current mode for 3 seconds to activate the Holiday Override setting mode. The plane icon will be displayed on the LCD and the user’s only option will be to set the number of holiday days (up to 31). To exit Holiday Override and turn On the relay, long press the key.

LCD Backlight
If AC is powered, or any key is pressed. The backlight will be turned off in the LCD backlight is activated when 15 seconds after all keys are released.

Factory Reset

If you want to return to the factory settings please press the Reset button once (use a pin for this action).

Technical Info

Product Specification
Model:	EP110
Type:	Surface Mounted Wired Single Channel Programmable Timer
Memory Backup	Lithium battery (CR2032 x1pc)
Power control
Rating	230V/50Hz/3(1)A
Relay	SPDT
Protection Rating:	IP 30
Environment
Operating Temperature/ Humidity:	0°C ~ 50°C, 10% – 90% non-condensing
Storage Temperature/ Humidity	-20°C~- 60°C, 10% – 90% non-condensing
Programs
Program	5-2 or 24hr individual program (selectable by jumper), 3 settings/day, with holiday override.
Boost Override	Yes, max 9 hours(selectable by software)
Holiday Override	Yes, max 31 days (selectable by software)
Clock
Clock Format	12 or 24 hour (selectable by software)
Clock Accuracy	+/-1 min/month
Daylight Saving Time (DST)	Yes, Clock automatically adjusted if DST is enabled.

Warranty

SALUS Controls warrants that this product will be free from any defect in materials or workmanship, and shall perform in accordance with its specification, for a period of two years from the date of installation. SALUS Controls’ sole liability for breach of this warranty will be (at its option) to repair or replace the defective product.

Customer Name: ………………………………………………………………………………………………………………………………………………
Customer Address: ………………………………………………………………………………………………………………………………………….
…………………………………………………………………………………………………. Post Code: ………………………………………………………
Tel No: …………………………………………………………. Email: …………………………………………………………………………………………
Company Name: ……………………………………………………………………………………………………………………………………………….
Tel No: ………………………………………………………… Email: …………………………………………………………………………………………..
Installation Date: ……………………………………………………………………………………………………………………………………………….
Installer Name: …………………………………………………………………………………………………………………………………………………..
Installer Signature: ……………………………………………………………………………………………………………………………………………

SALUS Controls PlcUnits 8-10 Northfield Business ParkForge Way, Parkgate, RotherhamS60 1SD, United Kingdom
Sales: T: +44 (0) 1226 323961
E: sales@salus-t ech.com
Technical: T: +44 (0) 1226 323961
E: tech@salus-tech.com

SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development, SALUS Controls plc reserves the right to change the specifications, designs, and materials of products listed in this brochure without prior notice. For the latest PFD Instruction Manual, go to www.salus-manuals.com

SALUS EP110 Single channel programmable Thermostat Installation Manual

The post SALUS EP110 Single channel programmable Thermostat Installation Manual appeared first on thermostat.guide.

source https://thermostat.guide/salus/salus-ep110-single-channel-programmable-thermostat-installation-manual/