SALUS HTRP230(50) Wired Digital THERMOSTAT Quick Guide

SALUS HTRP230(50) Wired Digital THERMOSTAT 

Introduction

The HTRP230V(50) from SALUS Controls is a stylish and accurate 5/2 or 24h programmable electronic thermostat with a large, easy-to-read Liquid Crystal Display (LCD). It is a surface-mounted temperature controller dedicated to surface heating/cooling, characterized by high thermal inertia. It is connected to the wired wiring center KL08NSB. The thermostat has the function of creating your own schedules. It can control group (SLAVE) thermostats – via the wiring center, it sends them an NSB (nighttime temperature reduction) signal and switches them to economic temperature. The time schedule is common to all thermostats (according to weekly (MASTER) thermostats), but temperatures are set individually on each thermostat. Thanks to the built-in algorithms, it offers much better temperature control accuracy than traditional mechanical thermostats. The thermostat is characterized by silent operation. The controller is characterized by silent operation.

Product Compliance

The product complies with the following EU directives: 2014/30/EU, 2014/35/EU, 2011/65/EU. Full information is available at www.saluslegal.com

Please note!
This document is a quick guide to the installation and operation of the product and indicates its main features and functions. Detailed information are in the full manual, which is available at www.saluscontrols.EU and which must be used for proper installation and operation of the product.

Safety information

Use in accordance with national and EU regulations. Use the device as intended and keep it dry. Product for indoor use only. Please read the entire manual before starting the installation and using the product.

Installation

Installation must be carried out by a qualified person, with appropriate electrical authorizations, in accordance with national and EU standards and regulations. The manufacturer shall not be liable for failure to comply with the manual.
NOTE:
There may be additional protection requirements for the entire installation.
The installer shall be responsible for compliance with such requirements.

Package content

Proper thermostat location

The ideal position to thermostat mounting is about 1,5m under floor level far from heating or cooling sources. In addition, the thermostat should not be installed behind curtains or other obstacles or in places with high humidity, as this will prevent accurate measurements of room temperature. The thermostat must not be exposed to sunlight. Do not place the thermostat on an outer wall.

Connection description

Note: The thermostat is compatible with the following Salus wiring center models: KL06 230V, KL08NSB 230V, KL04NSB 230V, or directly to the actuator.

Symbols explanation

Terminal	Description
L, N	Power supply (230V AC)
NSB	Night setback (input temperature reduction (230V ACoutput)
SL	230 V AC output signal
S1, N	Additional temperature sensors eg. FS300
CO	Switching jumper between heating and cooling (input 230V AC)

Note: The following designations are used interchangeably for products:

Montage

1. Make sure that the thermostat is not connected to the 230V AC.
   Then open the front housing using a screwdriver as shown above.
2. Connect the thermostat properly. Please refer to the “Connection description” section. Mount the thermostat using the designed screw.
3. Slide the front of the controller over the thermostat on the back of the controller cover. The thermostat is configured. Use buttons to set the temperature setpoint.

Button functions

LCD icon description

1. Day of the week
2. Hour
3. Program number
4. Active work mode
5. Economic mode
6. Economy mode
7. AUTO mode
8. PARTY mode
9. Holiday mode
10. Frost protection mode
11. Temperature unit
12. Heating mode
13. Manual mode/temp. override
14. Cooling mode
15. Additional temp. sensor
16. Current/set temp.

Time and date setting

Set the time and date during the first thermostat’s power-up.

The date and time can be set at any moment during thermostat use. Press any button to highlight the screen, then press and hold for 3 seconds, then follow steps from 3 to 9.

Manual mode – temperature setpoints

3 temperature levels are available. In manual mode, only one temperature level is maintained for the entire day. The icon in the frame indicates which mode is currently active. A different temperature can be set for each level.

• Comfort temperature mode
• Economic temperature mode
• Frost protection mode is Usually used during the period of absence or during the holidays (only available in HEATING mode).

The thermostat also has 2 additional modes:

• The PARTY mode sets the comfort temperature for a user-defined time (maximum 9 hours 50 minutes).
• The HOLIDAY mode sets the frost protection mode for a user-defined time (maximum 99 days).
  Press any button to highlight the screen, then follow the steps below:

Temperature setpoint

Press any button to highlight the screen, then follow the steps below:

AUTO mode – NSB function

The NSB (Night Setback) function enables automatic reduction of the temperature setpoint on the HTRS230(30) SLAVE thermostat, via the HTRP230(50) programmable MASTER thermostat connected to the wiring center (or another external clock). The temperature change takes place between the comfort temperature mode and the economic temperature mode.
To activate the AUTO mode, select the icon. Together with the icon, the thermostat shows the active temperature mode on the display: or.
Press any button to highlight the screen, then follow the steps below:

Note: For the proper NSB function work, an appropriate cable connection is required. The connection description is on the previous page.

Schedule programming

Press any button to highlight the screen, then follow the steps below:

Repeat steps 4 to 6 to set the time and temperature for further points of the schedule. No time (–:–) on the display means that the thermostat will skip the time interval. 6 points are available for the schedule.

Heating / Cooling mode

Manual change:
Modes are indicated by symbols. Press and hold the button to enter the menu, then use the button to select the Heating / Cooling mode change setting. Confirm changes using the button. Now use or buttons to set the heating or cooling mode. Confirm by button.

Automatic change (via CO terminal): The heating/cooling mode can be changed automatically via the CO terminal in the thermostat. If a 230 V AC power supply is connected to the CO terminal – then the thermostat automatically switches to cooling mode. If you want to use this function, then you have to change the value of the D18 parameter to “1”.

Cooling blocking:
When the D19 thermostat parameter is set to “1”, then cooling is blocked for a single room. When the cooling function is blocked, no message is displayed.

Installer mode

Press any button to highlight the screen, then follow the steps below:

Note: To restore default settings – set the P47 code during 2 steps and then confirm your choice using or buttons.

Installer parameters

xx	Function	Parameter Values	Description	Default Values
d01	Heating Control	0	According to the PWM algorithm	0
		1	Hysteresis 0.5°C (±0.25°C)
		2	Hysteresis 1.0°C (±0.5°C)
D02	Displayed temperature correction	-3.0°C to + 3.0°C	If the thermostat indicates an incorrect temperature, then it can be corrected ±3.0°C	0°C
D03	External sensor connection (S1/S2)	0	External sensor not connected	0
		1	External sensor connected
d04	External sensor used as Air sensor or Floor sensor	0	The D03 parameter must be set to “1” – then, if the D04 parameter is set to “0”, the thermostat only measures the temperature at the external sensor	0
		1	The D03 parameter must be set to “1” – then, if the D04 parameter is set to “1”, the sensor is used as floor overheating protection.
D05	Cooling Control	1	Hysteresis 0.5°C (±0.25°C)	2
		2	Hysteresis 1.0°C (±0.5°C)
D07	Valve Protection	0	Disabled	1
		1	Enabled
D08	Frost Setpoint	5°C – 17°C	The frost protection temperature is maintained for example during active holiday mode.	5°C
D09	12/24 Hour Format	0	12 hours	1
		1	24 hours
D10	Time zone (reserved for internet wireless)	from -13 to +13 hours	It gives you the possibility to fit the thermostat time zone to yours (every 1 hour step).	0
D11	Daylight Saving Time (DST)	0	Off	1
		1	On
D12	Heating setpoint limits	5°C – 35°C	Maximum temperature which can be set for heating	35°C
D13	Cooling setpoint limits	5°C – 40°C	The minimum temperature which can be set for cooling	5°C
D14	Floor sensor protection limit (heating high limit-HL)	11°C – 45°C	In order to protect the floor against overheating – heating will be turned off when the floor sensing temp is higher than the protection limit	27°C
D15	Floor sensor protection limit (heating low limit-LL)	6°C – 40°C	In order to protect the floor against overcooling – heating will be turned on when the floor sensing temp is lower than the protection limit	10°C
D16	Floor sensor protection limit (cooling)	6°C – 45°C	In order to protect the floor against overcooling – heating will be turned on when the floor sensing temp is lower than the protection limit	6°C
D17	Preset program selection	1-5	Select one of these 5 default programs. Once selected, the default program will overwrite the present program. The selected default programs can be edited by the user in the User Setting Mode.	1
D18	Heat/Cool Mode Selection	0 or 1	0: Manual with buttons use 1: Automatic by the CO terminal	0
D19	Cooling Blocking function heating/cooling	0 or 1	0: Cooling disabled 1: Cooling allowed	0
D20	Actuators loading selection for different temperature compensation	1 to 5	Numbers 1 to 5 are the numbers of actuators connected to the thermostat.	1

Salus Limited
6/F, Building 20E, Phase 3, Hong Kong Science Park, 20 Science Park East Avenue, Shatin, New Territories, Hong Kong

support@salus-controls.de
tel: +49 6108 8258515
technicalsupport@saluscontrols.fr
tel: +33 (0) 134 724 039
tech@salus-tech.com
tel: +44 (0) 1226 323961
www.salus-controls.eu

SALUS Controls is a member of the Computime Group Maintaining a policy of continuous product development SALUS Controls plc reserves the right to change the specification, design and materials of products listed in this brochure without prior notice.
Issue date: 03 2021
Version: V016

SALUS HTRP230(50) Wired Digital THERMOSTAT Quick Guide

The post SALUS HTRP230(50) Wired Digital THERMOSTAT Quick Guide appeared first on thermostat.guide.

source https://thermostat.guide/salus/salus-htrp23050-wired-digital-thermostat-quick-guide/